sihyde|Automatic Drop Compensation|Why Powder Overweighs

banner
sihyde Automatic Drop Compensation: Why Powder Overweighs
November 07, 2026

The dosing section meets the same scene every day: the scale approaches its target, the screw stops, and material keeps falling. That last trickle never appears in the recipe sheet, and nobody stops the line for it. Automatic drop compensation is the function that deals with this inertia, closing the feed early and deducting the result, so each batch returns to its set point and the error stops accumulating from batch to batch.
塔楼式7_副本

What exactly does the compensation correct?

• The material still in the air — A valve closes, and some material keeps falling. The controller takes that amount off the target and settles the batch on the net figure, so the recipe returns to its set point. It looks small in one batch and turns into a stock shortfall at month end.

• It only exists if it is in the electrical scope — Automatic drop compensation and automatic cut-off belong in the electrical schedule; that is what puts them inside the delivery. A verbal promise is not a configuration, and at acceptance there is nothing to point at. Written into the annex, it can be checked during commissioning.

• Every deduction needs a record — Each cut-off should leave a trace that can be reviewed after a recipe change. Without the record, the function reduces to a name on a specification sheet.

Why does the additive drop matter more?

• Small share, high sensitivity — Cellulose ether and redispersible powder are dosed in tiny amounts, and a little extra is enough to change the consistency of a whole batch. The finer the recipe, the more visible that trickle becomes on the trowel.

• The range has to match — The small dosing section needs a small-range load cell and a stainless hopper. A large scale weighing a small addition has no resolution to spare, so compensation cannot express itself; oversizing the range dilutes resolution across the whole span.

• Record it per silo — Every material flows differently, so compensation has to be stored per silo. One set of parameters for all silos has to be retuned at every changeover, and the more silos a plant has, the more that record saves.

How is the compensation verified at acceptance?

• Read consecutive batches — One good batch proves nothing. Put the weighing records of several consecutive batches side by side and it is clear whether the deviation is converging or drifting. The longer the record kept, the clearer the trend, and it also serves after-sales diagnosis.

• Sample by the standard method — Check against the sampling and judgement method of the ready-mixed mortar standard. Name the standard only; where the edition year is uncertain, leave it out of the contract. Agree the method before acceptance day, or both sides arrive with a different document.

• Calibrate first — Weight calibration usually sits with the buyer. Tuning parameters on an uncalibrated scale means correcting on the wrong baseline, and the more it is adjusted the further it drifts. File the calibration record with the compensation parameters so the next shift can pick it up.

Which lines need it most?

• Frequent recipe changes — A multi-product plant changes recipe several times a day. Automatic drop compensation stores parameters by product, so a changeover does not start from zero, and every added product makes that library worth more.

• Many additive types — Additives split across several silos, each recording its own drop, keep the ratio steady and make small custom orders safe to accept. With the small components settled, the large ones can run faster.

• Hopper size against batch size — An oversized hopper with a small batch raises the relative effect of the drop. Hopper volume has to match the batch for compensation to mean anything, and that decision belongs to the selection stage; changing it later means new scales.

Frequently asked questions

Q1: How should this function be written into the contract?

A1: Write the function and the way it will be verified: the control system provides automatic drop compensation and automatic cut-off, and at acceptance the supplier provides consecutive batch records for the same recipe, checked against the ready-mixed mortar standard.

Q2: Without the function, can operators top up by hand?

A2: Manual topping up rescues a single batch, not a trend. The deviation between batches accumulates, and the difference only shows up when the silos are counted at month end, long after the cause has passed.

Q3: Do the parameters drift once they are adjusted?

A3: They do, if they are not fixed. Parameters should be stored per product and per silo; adjusting them at will means every batch is a trial. Change one, record one, and the parameter table becomes a handover document in its own right.

What to write into the electrical schedule

The value of automatic drop compensation is not in the name of the function but in every batch landing back on its set point. Write it into the electrical schedule, keep the records, store the parameters by product, and the ratio moves from experience to a process that can be repeated by anyone on the shift.

Inquiry Now

sihyde01@163.com

+66961148624

+66961148624